If y'all always encountered an error and don't know what to do, Windows 10 comes equipped with troubleshooting tools to fix information technology for you. I of those convenient tools is the automatic repair tool. It is a handy repair feature that can troubleshoot bug that end you from booting correctly.

But, what do yous exercise when the tool itself is the crusade of the fault? If your PC is stuck in an automatic repair loop, we have devised a list of solutions to fix your error.

What Is an Automatic Repair Loop and What Causes It?

An automatic repair loop is an error that occurs when Windows 10 tries to kicking and fails, and then forcefully boots upwardly the automatic repair tool and tries to repair itself. When Windows can't repair itself, it reboots and repeats itself in an endless cycle.

At that place isn't a single cause for a Windows 10 automatic repair loop and they can be hard to figure out. The nigh common cause tends to be missing or corrupted organization files, in which Windows can't kick or repair itself because these essential files information technology needs to run aren't available.

Missing device drivers also tend to be 1 of the biggest causes for the error. If y'all have recently upgraded your PC, your new components will need device drivers to allow Windows to use them. If the drivers are missing, out-of-date, or not supported, they could crusade a repair loop. New peripherals can besides cause this error if their drivers aren't installed correctly.

Other possible causes tend to be related to faulty components, malware infections, corrupted system registries, and even cleaved installation files. Simply, there is no need to worry every bit our solutions will work for virtually causes of a Windows 10 automatic repair loop.

1. Run Fixboot and Chkdsk Commands

If you can't place any cause of a Windows x automated repair loop, you tin use some system repair tools to try to prepare it. The chkdsk command starts a low-level check of your organization drive for errors using the Bank check Disk utility. If it detects errors, it will automatically repair them.

While Windows tin't kick, you can still force Windows to boot to a Command Prompt window using the Advanced options card screen.

To exercise this:

  1. Restart your PC and printing the F8 key on your keyboard before the Windows logo and spinning icon appear. This will cause the Windows boot troubleshooting carte du jour to appear. Select See advanced repair options to begin.
  2. From the Choose an selection screen, select Troubleshoot > Advanced options > Command Prompt.
    Advanced startup repair Windows 10
  3. In the Command Prompt window, type the post-obit control and press Enter:
                  chkdsk c: /r
  4. If the chkdsk control fails, you can likewise try using the Fixboot command. In the same Control Prompt window, enter the following control and press Enter:
                  fixboot c:
  5. One time you lot are finished, close the Command Prompt window and restart your PC.

2. Perform a Organization Browse in Condom Fashion

If system repair tools find corrupted files, Windows replaces those files with the local paradigm. However, if this image itself has become corrupted, Windows can't repair itself and causes the previous commands to fail. To repair this, we can use the DISM (Deployment Epitome Servicing and Management) tool.

To apply this tool, we first must enable Prophylactic Mode. This loads a basic version of Windows without any tertiary-party programs to help you fix your commencement-upward errors.

  1. The first step, like before, is to restart your PC and press the F8 key while booting to open the Windows boot troubleshooting menu.
  2. Select See advanced repair options > Troubleshoot > Avant-garde options > Startup Settings > Restart.
  3. Now, you will see a list of various restart options. Choose Enable Safe Way with Networking by selecting F5 on your keyboard.
  4. In one case Windows boots up in Safe Mode, correct-click the Outset carte and select Windows PowerShell (Admin).
  5. In the PowerShell window, type the following command and press Enter:
                  DISM /Online /Cleanup-Image /RestoreHealth
  6. This volition take some time to finish. When the DISM tool finishes running, reboot your PC and follow the above steps to open the PowerShell window in Condom Manner over again.
  7. This time, type the following control and press Enter:
                  sfc /scannow
  8. This will check the integrity of Windows organization files and allow us to verify if Windows is fully repaired.

3. Restore the Windows Registry

Sometimes, malware infections or disk issues tin can too end up corrupting the registry files.

To fix registry issues, you can restore it with the post-obit steps:

  1. Open the Windows boot troubleshooting menu.
  2. Select See advanced repair options > Troubleshoot > Avant-garde options > Command Prompt.
  3. Type the post-obit command and press Enter:
                  C:\Windows\System32\config\\rregback* C:\Windows\System32\config\
  4. If you are asked to overwrite files, type All and printing Enter.
  5. One time you are finished, restart your PC.

If you believe that your Windows is functional, you lot can endeavour to disable the automatic startup repair organization. This should permit you to boot into Windows without the repair loop taking identify. However, this will only work if your Windows arrangement is working properly. You lot can utilize it to determine if your Windows is really at fault.

To disable Windows ten automatic repair tool, follow these steps:

  1. Open the Windows boot troubleshooting menu.
  2. Select Meet avant-garde repair options > Troubleshoot > Advanced options > Command Prompt.
  3. Type the following command and press Enter: bcdedit
  4. Cheque the values for identifier and recoveryenabled. The identifier value should be {default} and recoveryenabled should be yes.
  5. At present, blazon this command and printing Enter:
                  bcdedit /ready                {default} recoveryenabled no
  6. This will disable the automatic boot repair. If the command doesn't work, try the following command:
                  bcdedit /prepare                {current} recoveryenabled no
  7. Once you are finished, restart your PC.

v. Reset Your Windows 10 Device

The last resort for a figurer stuck in an automatic repair kick loop is resetting Windows 10. You don't take to worry about losing your files and data as you have an choice to go along with either a clean reset (deleting everything) or preserve your files.

To reset a Windows 10 PC, open the Windows boot troubleshooting bill of fare and select Troubleshoot > Reset this PC.

reset windows

Dealing With the Automatic Repair Loop

It tin exist frustrating to deal with a never-ending loop due to a tool meant to resolve your bug. Information technology can be difficult to diagnose and understand, only our solutions volition be sure to help y'all out and return your PC to normal.

How to Set the Windows Stop Code Retentiveness Management BSOD

Read Side by side

Most The Author

Maxwell Holland (42 Articles Published)

Maxwell is a software developer who works as a writer in his spare time. An gorging tech enthusiast who loves to fiddle in the world of artificial intelligence. When he isn't busy with his piece of work, he is off reading or playing video games.

More than From Maxwell The netherlands